topic Re: dialog Program issue in Application Development and Automation Discussions

dialog Program issue

former_member184495 — Thu, 01 Jun 2006 07:44:02 GMT

hi,

i have a transaction "ZA"

the screen ZA has a text field zemp-name and is set to invisible mode.

now can i change this mode to visible through the program ?

rewards for sure.

cheers

Aditya.

Re: dialog Program issue

Former Member — Thu, 01 Jun 2006 07:46:27 GMT

Hi aditya,

if ZA transaction points to Z prog then you can,

by writing code in AT SELECTION SCREEN.

Re: dialog Program issue

Former Member — Thu, 01 Jun 2006 07:47:58 GMT

In PBO of the screen.

loop at screen.

if screen-name = 'xxxx'.

screen-invisible = 0.

endif.

modify screen.

endloop.

Regards,

Ravi

Re: dialog Program issue

Former Member — Thu, 01 Jun 2006 07:47:59 GMT

go to screen painter(layout)

there is in properties..

3 tab strip in bottom in one of the tab strip there is option for that..just uncheck invisible check...

or if u want to change it by programm for certain things than do the same as ravi reply..

Re: dialog Program issue

Former Member — Thu, 01 Jun 2006 07:52:23 GMT

Hi,

You can use the following coding under

At selection-screen event:

Loop at screen.

if screen-name = 'name'.

screen-invisible = '0'.

modify screen.

endif

endloop.

Re: dialog Program issue

Former Member — Thu, 01 Jun 2006 07:54:55 GMT

Hi Aditya,

In the PBO of the screen, write this code.

Suppose the field name is 'FIELD1'.

LOOP AT SCREEN.

IF SCREEN-NAME = 'FIELD1'.

SCREEN-ACTIVE = 1.

MODIFY SCREEN.

ENDIF.

ENDLOOP.

You can also use SCREEN-INVISIBLE = 0.

If you want the field to be Input/Output and Visible, Just write SCREEN-ACTIVE = 1. It is similar to

SCREEN-INPUT = 1.

SCREEN-OUTPUT = 1.

SCREEN-INVISIBLE = 0.

Regards,

SP.

Re: dialog Program issue

Former Member — Thu, 01 Jun 2006 08:01:20 GMT

Hi,

in your PBO of the screen you have to write this code.


loop at screen.
if screen-name = 'SCREENFIELD'.
screen-invisible = 0.
endif.
modify screen.
endloop.

Regards

vijay

Re: dialog Program issue

Former Member — Thu, 01 Jun 2006 08:02:10 GMT

Hello Aditya,

There are two aspects in this. I am assuming this is a custom development. If you permanantly want to change this then u can go to screen painter and change the attribute for the field. However if you want to do programatically under certain condition then in PBO section of the screen,

Loop at screen.

if screen-name = 'whatever in the field name'

screen-invisible = '0'.

modify screen.

endloop.

Re: dialog Program issue

Former Member — Thu, 01 Jun 2006 08:05:06 GMT

Hi,

Just put this code at your PBO Module.


  LOOP AT SCREEN.
    IF SCREEN-NAME CS 'FIELD1'.
        SCREEN-ACTIVE  = '1'.
        SCREEN-OUTPUT  = '1'.
        SCREEN-INVISIBLE = '1'.
        MODIFY screen .
    ENDIF.
  ENDLOOP.

Regards,

Re: dialog Program issue

former_member184495 — Thu, 01 Jun 2006 08:46:42 GMT

hi,

as said ...

i did that, but isnt working...

the screen ZA field is set with input as 'possible'

still it isnt working,

i might be wrong somewhere,

but...

thanks,

shall reward all those which were worth.

Aditya.

Re: dialog Program issue

Former Member — Thu, 01 Jun 2006 11:17:05 GMT

Hi Aditya,

Is your problem solved??

I just got the solution to your problem..

Goto the attributes of the field.

In the Program tab, just give uncheck Output only checkbox and Input Checkbox. so that it is neither Input nor output.

In the Display tab, just check the Invisible checkbox.

Now in the PBO of the program, just code like this..

LOOP AT SCREEN.

IF SCREEN-NAME = 'name of the field'.

SCREEN-INVISIBLE = 0.

SCREEN-INPUT = 1.

SCREEN-OUTPUT = 1.

MODIFY SCREEN.

EXIT.

ENDIF.

ENDLOOP.

This will work..

Regards,

SP.

Message was edited by: Sylendra Prasad

Re: dialog Program issue

abdul_hakim — Thu, 01 Jun 2006 11:22:39 GMT

hi in the PBO event you write the below code..

LOOP AT SCREEN.

IF SCREEN-NAME = 'XYZZ'.

SCREEN-INVISIBLE = '0'.

MODIFY SCREEN.

ENDIF.

ENDLOOP.

Cheers,

Abdul Hakim

Mark all useful answers..

Re: dialog Program issue

former_member184495 — Tue, 01 May 2007 06:51:32 GMT

answered