topic Re: Idoc help in Application Development and Automation Discussions

Idoc help

Former Member — Wed, 03 May 2006 19:36:11 GMT

Hi,

I am sending Gl master idocs GLMAST from one system to another . In the other system i have assigned a Z process code, in the Z process code FM , i am calling the standard GLMAST FM and sending back the status of this Idoc back to the sending system.

My problem is that when i send the idocs to the other system , the idoc fails giving the message 'Function module not allowed' , please advice y this is hapenning , when i tried to repost the same idoc through WE19 , i am able to run the idoc successfully through the Z FM and post the data , but when the idocs are recieved by the system , it fails . Please help.

Kunal

Re: Idoc help

Former Member — Wed, 03 May 2006 19:37:54 GMT

Go to BD51, and insert an entry with the Z-FM name as inbound.

Re: Idoc help

Former Member — Wed, 03 May 2006 19:39:31 GMT

The entry is already present in bd51

Re: Idoc help

Former Member — Wed, 03 May 2006 19:43:01 GMT

Hi,

are you using the FM <b>IDOC_INPUT_GLMAST</b> or some thing else.

Regards

vijay

Re: Idoc help

Former Member — Wed, 03 May 2006 19:44:26 GMT

I guess then problem is in the function module interface. Compare it with any of the standard idoc inbound posting FMs e.g. IDOC_INPUT_*

It's not either RFC-enabled or some parameter/table is incorrectly defined.

Re: Idoc help

Former Member — Wed, 03 May 2006 19:47:03 GMT

The problem is not with the interface as i am using the same process code for other master data types like workcenters , asset master etc.. and the idocs there no not fail . I think the problem is to do with the assigning of the process code with the business object , if anyone knows please help.

Yes , the FM which gets called inside is IDOC_INPUT_GLMAST

Re: Idoc help

Former Member — Wed, 03 May 2006 19:49:07 GMT

Did you miss the WE57 by any chance where we assign the FM to the idoc and message type?

Re: Idoc help

Former Member — Wed, 03 May 2006 19:52:22 GMT

Hi Kunal,

<i>I think the problem is to do with the assigning of the process code with the business object</i>

i think even i am feeling the same....

Regards

vijay

Re: Idoc help

Former Member — Wed, 03 May 2006 19:55:49 GMT

Hi Kunal,

Try to check the function module direction given in WE52 or WE57. ( i din't remember the tcode. Have you given the direction as 2 or 1). 2 is for Inbound.

shylesh

Re: Idoc help

Former Member — Wed, 03 May 2006 20:04:40 GMT

Kunal,

Please award points if it solved your problem and close the thread.

Re: Idoc help

Former Member — Wed, 03 May 2006 20:39:50 GMT

Hi Kunal,

Please check this links on how to setup inbound processing.

Perhaps you missed an important step.

http://help.sap.com/saphelp_erp2004/helpdata/en/dc/6b835943d711d1893e0000e8323c4f/content.htm

http://www.sapgenie.com/sapgenie/docs/ale_scenario_development_procedure.doc

Hope this will help.

Regards,

Ferry Lianto

Re: Idoc help

Former Member — Thu, 04 May 2006 16:23:26 GMT

Hi,

I checked the FM direction in WE57 , and for all business objects it shows 2 , which is inbound , so this is not the problem.

Kunal