topic Re: GUI Title in Application Development and Automation Discussions

GUI Title

Former Member — Mon, 03 Oct 2011 09:58:17 GMT

Dear Friends,

I had a table maintenance view, and it was functioning properly.

According to my requirement, I changed there title bar with following code.

But when I activated the new code,maintenance view functions (back, save, ...) are not worked and impossible to rollback.

Please tell me what was happened and how can I fixed this issue.

I hope you will clear my problem.


PROCESS BEFORE OUTPUT.
 MODULE LISTE_INITIALISIEREN.
   MODULE TITLEBAR.
 LOOP AT EXTRACT WITH CONTROL


module TITLEBAR output.
SET TITLEBAR '0001'.
endmodule.                 " TITLEBAR  OUTPUT

Thanks in Advance

Re: GUI Title

Former Member — Mon, 03 Oct 2011 10:05:24 GMT

This message was moderated.

Re: GUI Title

Former Member — Mon, 03 Oct 2011 10:08:34 GMT

When you create a maintenance view screen, titles etc. are automatically generated

When you write your code in it, it may not work as intended..

I think you hv to roll back the change using version management, try removing the title see if it works as previously

BR,

Rahul

Re: GUI Title

koolspy_ultimate — Mon, 03 Oct 2011 10:11:09 GMT

Hi i guess u forgot about the gui functions.

or the gui is not activated.

activate it again and check again.

Regards,

koolspy.

Re: GUI Title

Former Member — Mon, 03 Oct 2011 10:17:47 GMT

WRITE THE QUERIES FOR BACK & SAVE & ACTIVATE THEM...

SO THAT THE GUI FUNCTION S WILL WORK....

THANKS,

CHAITANYA

Re: GUI Title

former_member528040 — Mon, 03 Oct 2011 10:59:25 GMT

I think regenerating the User Interface should solve the problem. Just go to the user interface - double click on titlebar - 001. Or go to SE41.

Re: GUI Title

Former Member — Tue, 04 Oct 2011 05:40:32 GMT

how can i activate GUI functions?

Re: GUI Title

Former Member — Tue, 04 Oct 2011 05:46:12 GMT

Please WRITE THE QUERIES FOR BACK & SAVE & ACTIVATE THEM...

AND Declare function Code in GUI.

define Status in PBO AND Queries in PAI USER_COMMAND.

Regards

Ajit

Edited by: ajitabap on Oct 4, 2011 7:51 AM

Re: GUI Title

koolspy_ultimate — Tue, 04 Oct 2011 05:59:42 GMT

Hi,

this is already discussed by ajit

you need to write the queries for back, save and what ever you require and Declare function Code in GUI.

Next define pf-status in PBO and Queries in PAI USER_COMMAND.

Regards

Koolspy.

Re: GUI Title

Former Member — Tue, 04 Oct 2011 07:04:08 GMT

Hi Friends,

I tried that solution so many times.

when i put the code below, title will change and no any other functions work even PAI not trigger. it says choose a valid function

Re: GUI Title

Former Member — Tue, 04 Oct 2011 08:33:12 GMT

Hi Nelson,

I tried to change guii title of a screen of table maintanance. Its working fine. I believe you need to check your title is active and activate entire function group, including your include where Title code exists. Activate entire function group ... no need of additional handling of standard functions..

Regards,

Ravi.

Re: GUI Title

Former Member — Tue, 04 Oct 2011 09:50:05 GMT

can you please send me the steps you had to follow?

Re: GUI Title

Former Member — Tue, 04 Oct 2011 10:50:40 GMT

My Dear Friend I will Provide you The Detail Document regarding this....

Regards

Ajit

Re: GUI Title

Former Member — Tue, 04 Oct 2011 12:15:01 GMT

Hi Nelson,

If i understand correctly.. This may help you..

se11 - change

Utilities-> table maintanance generator

note the function group name

open in se80

in screens select your screen

write module title_bar in pbo.

double click title_bar to create module.

create module in new include.

SET TITLEBAR '0001'. double click '0001'

enter title name

select all tittle

activate title bar.

back

activate screen.

activate entire funtion group..

Regards,

Ravi.

Re: GUI Title

Former Member — Wed, 05 Oct 2011 03:31:53 GMT

Hi Ravi,

Thank you very much!