topic Re: Tabbed selection screen problem. in Application Development and Automation Discussions

Tabbed selection screen problem.

snursalim — Thu, 28 May 2009 03:12:02 GMT

Hi expert,

I need some help in creating my selection screen.

Right now i'm creating a tabbed selection screen as the code below follows.


PARAMETERS: p_test AS CHECKBOX USER-COMMAND testrun DEFAULT 'X'.

SELECTION-SCREEN BEGIN OF SCREEN 100 AS SUBSCREEN.
PARAMETERS: p_offkdt TYPE sy-datum MODIF ID thr.
SELECT-OPTIONS: s_konfe FOR p0002-konfe.
SELECTION-SCREEN END OF SCREEN 100.

SELECTION-SCREEN BEGIN OF SCREEN 200 AS SUBSCREEN.
SELECTION-SCREEN: BEGIN OF LINE,
                   COMMENT 1(20) text-005 MODIF ID yea
                    FOR FIELD p_lowdt,
                    POSITION POS_LOW.
PARAMETERS: p_lowdt TYPE begda MODIF ID yea,
            p_updt TYPE endda MODIF ID yea.
SELECTION-SCREEN: END OF LINE.
PARAMETERS: p_keydt TYPE dats MODIF ID yea.
SELECTION-SCREEN END OF SCREEN 200.

SELECTION-SCREEN BEGIN OF SCREEN 300 AS SUBSCREEN.
PARAMETERS: p_lvdat TYPE dats MODIF ID lv.
SELECTION-SCREEN END OF SCREEN 300.

SELECTION-SCREEN: BEGIN OF TABBED BLOCK prog_selection FOR 4 LINES,
                  TAB (20) button1 USER-COMMAND push1,
                  TAB (20) button2 USER-COMMAND push2,
                  TAB (20) button3 USER-COMMAND push3,
                  END OF BLOCK prog_selection.

Now as I'm using tab and subscreen, therefore i need to initialize the subscreen which i wanted to use which i did in the initialization event.

 
  prog_selection-dynnr = 100.
  prog_selection-activetab = 'PUSH1'.

With the above code, my default tab would be screen 100 which is the first tab.

My problem right now is, after i execute the program, and then i press the back button to go back to the selection screen, the default tab 100 is shown again while i wanted to show the last tab which was picked before the program was executed. Please kindly advise how can i solve this problem.

Many Thanks!

-Suwardi Nursalim-

Re: Tabbed selection screen problem.

Former Member — Thu, 28 May 2009 03:49:30 GMT

Hi..

In the initialization part dont hardcode the Active tab as Push1.. Instead define a variable where you store the value of Pressed tab.. Say g_pressed_tab.. and in initialization part assign the value of active_tab to g_pressed_tab..

Hope this solves your problem...

Regards,

Kanchan

Re: Tabbed selection screen problem.

Former Member — Thu, 28 May 2009 04:19:18 GMT

Hi,

DATA: V_DYNNR TYPE SY-DYNNR VALUE '0100',

V_ACTIVETAB(4).

INITIALIZATION.

MOVE 'PUSH1' TO V_ACTIVETAB.

AT SELECTION-SCREEN OUTPUT.

prog_selection-dynnr = V_DYNNR.

prog_selection-activetab = V_ACTIVETAB.

When the user clicks each tab of the tab strip.*

CASE SY-UCOMM.

WHEN 'PUSH1'.

V_ACTIVETAB = 'PUSH1'.

(rest of your code).

WHEN 'PUSH2'.

V_ACTIVETAB = 'PUSH2'.

(rest of your code).

WHEN 'PUSH3'.

V_ACTIVETAB = 'PUSH3'.

(rest of your code).

ENDCASE.

Hope this will help you.

Regards,

Smart Varghese

Re: Tabbed selection screen problem.

Former Member — Fri, 21 Jan 2011 04:47:36 GMT

I am also facing same problem.

At initialization all the variables are initialized.

So how this variable be assigned?