topic Re: Data hidden by Screen Modifications in Application Development and Automation Discussions

Data hidden by Screen Modifications

Former Member — Thu, 21 May 2009 04:45:49 GMT

Hi All

I am modifying TCode PA30. Some fields & 2 table controls are added in new screen.

When displaying the data, only the data of the fields are getting displayed but data of table control in not displayed.

Instead a message in Status Bar is showing "Data hidden by Screen Modifications".

Any suggestions.?

Regards.

Re: Data hidden by Screen Modifications

Former Member — Thu, 21 May 2009 05:51:51 GMT

Hai nikhil,

Can you please mention the BADI or exit that you used for modification, that would be quiet useful.

Warm Regards,

Suvendu

Re: Data hidden by Screen Modifications

Former Member — Thu, 21 May 2009 05:58:05 GMT

Hi Suvendu

I have created new Infotype using TCode PM01.

It automatically creates a default screen. After that I have added some fields & table controls.

Regards.

Re: Data hidden by Screen Modifications

Former Member — Fri, 22 May 2009 04:10:36 GMT

The data is not getting populated in table control.

Is the code correct?


  LOOP AT   T_ARBZT
       WITH CONTROL TARB
       CURSOR TARB-CURRENT_LINE.
     MODULE TARB_get_lines.
  ENDLOOP.

MODULE TARB_GET_LINES OUTPUT.
  DESCRIBE TABLE T_ARBZT  LINES g_tarb_lines.
ENDMODULE.

Re: Data hidden by Screen Modifications

Former Member — Fri, 22 May 2009 04:46:12 GMT

Hi Nikhil.

Small change to your code

LOOP AT T_ARBZT

WITH CONTROL TARB

CURSOR TARB-CURRENT_LINE.

MODULE TARB_get_lines.

ENDLOOP.

MODULE TARB_GET_LINES OUTPUT.

DESCRIBE TABLE T_ARBZT LINES g_tarb_lines.

Move-corresponding T_ARBZT to <table control table parameter>

ENDMODULE.

your table control must be having parameter

ex. MARA-matnr, MARA-ernam, MARA-erdat

then pass

Move-corresponding T_ARBZT to MARA.

This will surely solve your problem.

Cheers,

Suvendu

Re: Data hidden by Screen Modifications

Former Member — Fri, 22 May 2009 05:59:58 GMT

Thanks for reply Suvendu.

Actually my table control parameters are T_ARBZT-BEGDA, T_ARBZT-ENDDA etc....

In that case, what should I write?

Re: Data hidden by Screen Modifications

Former Member — Fri, 22 May 2009 06:07:02 GMT

LOOP AT T_ARBZT

WITH CONTROL TARB

CURSOR TARB-CURRENT_LINE.

MODULE TARB_get_lines.

ENDLOOP.

MODULE TARB_GET_LINES OUTPUT.

DESCRIBE TABLE T_ARBZT LINES g_tarb_lines.

Move T_ARBZT to T_ARBZT.

ENDMODULE.

MODULE TARB_GET_LINES OUTPUT.

READ TABLE T_ARBZT INDEX tarb-current_line.

ENDMODULE.

try this incase if doesn't work then please revert back.

The problem is what I think the screen variable is carring nothing to the table control and therefore nothing is getting printed.

Best Regards,

Suvendu

Edited by: Suvendu Swain on May 22, 2009 11:41 AM

Re: Data hidden by Screen Modifications

Former Member — Fri, 22 May 2009 06:48:51 GMT

Dear Suvendu

I have tried these also, but again data is not coming in the table control.

When I'm checking IT, data is populating perfectly.

Re: Data hidden by Screen Modifications

Former Member — Fri, 22 May 2009 09:16:32 GMT

Any Suggestions.?

Re: Data hidden by Screen Modifications

Former Member — Sun, 24 May 2009 06:20:21 GMT

Just change your screen name to ARBZT and declare the same in TOP include

and try this code. I think the program is not able to make out with similar kind of names.


LOOP AT T_ARBZT
WITH CONTROL TARB
CURSOR TARB-CURRENT_LINE.
MODULE TARB_get_lines.
ENDLOOP.

MODULE TARB_GET_LINES OUTPUT.
Move T_ARBZT to ARBZT.
ENDMODULE.

OR
MODULE TARB_GET_LINES OUTPUT.
READ TABLE T_ARBZT INDEX tarb-current_line.

ENDMODULE.

Hope this works out.

Best of luck.

Suvendu

Re: Data hidden by Screen Modifications

Former Member — Mon, 25 May 2009 03:55:08 GMT

try this

SE51

PBO

module_screen_0800.

module_display_screen.---> this module for screen modifications

whether to display in enable or disable mode.

PAI

module_user_command_0800.

module read_data.

se38

module_screen_0800.

loop at screen.

do screen modifications here

endloop.

endmodule.

module read_data.

read itab with key tablecontrol-currentline

if sy-subrc = 0.

move-corresponding itab to itab1.

endif.

endmodule.

Regards