topic Re: Help for coming out from Loop...Endloop in Application Development and Automation Discussions

Help for coming out from Loop...Endloop

Former Member — Thu, 12 Mar 2009 11:35:10 GMT

Dear All,

I have one internal table with 10000 records . I want to read a specific record with certain WHERE clause with logical operators.

Now my requirement is that as soon as that condition is satisfied , control should go to next line after Endloop BUT NOT to the next loop pass so that it will not read remaining entries.

Suggestions are most welcome.

Thanks...........

Re: Help for coming out from Loop...Endloop

Former Member — Thu, 12 Mar 2009 11:36:23 GMT

Hi,

Use Command: EXIT.

Thanks.

Re: Help for coming out from Loop...Endloop

Former Member — Thu, 12 Mar 2009 11:37:08 GMT

EXIT. command should work.

Re: Help for coming out from Loop...Endloop

Former Member — Thu, 12 Mar 2009 11:37:16 GMT

Try this..

Loop at itab.

if <Condition>.

EXIT.

endif.

Endloop.

Re: Help for coming out from Loop...Endloop

Former Member — Thu, 12 Mar 2009 11:37:53 GMT

EXIT

Re: Help for coming out from Loop...Endloop

Former Member — Thu, 12 Mar 2009 11:38:59 GMT

Hi,

Using EXIT we can come out of the loop.

By using CONTINUE we can come out of the current iteration.

Regards,

Surya kiran

Re: Help for coming out from Loop...Endloop

Former Member — Thu, 12 Mar 2009 11:39:22 GMT

hi;

there are 2 ways

loop where condition

endloop.

loop

if condition

exit.

endif.

endloop.

Regards

Shashi

Re: Help for coming out from Loop...Endloop

Former Member — Thu, 12 Mar 2009 11:41:46 GMT

Hi,

Use exit command.

Loop at itab into wa.

if wa-field = 'CONDITION'.

EXIT.

endif.

endloop.

Cheers,

Rudhir

Re: Help for coming out from Loop...Endloop

Former Member — Thu, 12 Mar 2009 11:42:25 GMT

If you are looking to read specific record why do you require LOOP .. WHERE .

Please use READ TABLE WITH KEY... which will read only required record and you are process further processing.

This will improve performance over LOOP ...

Edited by: Sunil Sawaikar on Mar 12, 2009 12:42 PM

Re: Help for coming out from Loop...Endloop

Former Member — Thu, 12 Mar 2009 11:46:55 GMT

Hi,

Data is huge so make use off field symbol. Follow the below logic.

Field-symbol : <fs_wa_tab> type wa_tab.

Loop at i_tab assigning <fs_wa_tab>.

if (condition)

..........................

exit.

endif.

endloop.

Thanks,

Asit Purbey.

Re: Help for coming out from Loop...Endloop

faisalatsap — Thu, 12 Mar 2009 11:49:46 GMT

Hi,

You can use

RETURN

Kind Regards,

Faisal

Re: Help for coming out from Loop...Endloop

Former Member — Thu, 12 Mar 2009 11:57:01 GMT

hi after select stmt write this.

select * _______

if sy-dbcnt eq 0.

do this.

else.

go to next line code here.

endif.

Re: Help for coming out from Loop...Endloop

Former Member — Thu, 12 Mar 2009 12:02:20 GMT

Hi,

if the conditions gives you a single record or you want to exit the loop as soon as atleast one record is read then make use of read statement instead of loop...endloop.

read table <tabname> into <workarea> with key <conditions>.
if sy-subrc = 0. " means the record is found... write the steps you have written after endloop if its found...
endif.

if the conditions gives you multiple records, then use loop and if you want to exit on certain condition...

then use loop....endloop.

loop at itab into wa  where conditions.
  if <condtition>.
       exit.
  endif.
endloop.

Regards,

Siddarth