topic Re: Module pool Program table control in Application Development and Automation Discussions

Module pool Program table control

Former Member — Tue, 03 Feb 2009 09:37:45 GMT

Hi,

In Module pool programming, table control i have 10 items out of which in the same colum i want to put them in edit mode and certain in disply mode.

Regards

Re: Module pool Program table control

Former Member — Tue, 03 Feb 2009 09:46:00 GMT

Hi,

You can use loop at screen,



MODULE passdata OUTPUT.

  READ TABLE it_revision INTO wa_rev INDEX tab_clc-current_line.
  IF sy-subrc = 0.
    LOOP AT SCREEN.
      IF screen-group1 = '111'.      " 111 IS THE GROUP NAME
        screen-input = 1.          " input mode
        screen-active = 1.         " input mode.
        MODIFY SCREEN.
      ENDIF.
    ENDLOOP.
  ELSE.
    LOOP AT SCREEN.
      IF screen-group1 = '111'.       "GROUP NAME
        screen-input = 0.           " display mode
        screen-active = 1.          " DISPLAY MODE.
        MODIFY SCREEN.
      ENDIF.
    ENDLOOP.
  ENDIF.
ENDMODULE.                 " PASSDATA  OUTPUT

Make the group of those field ,that you want in input mode

Hope it will Solve your problem

Thanks

Arun kayal.

Re: Module pool Program table control

former_member673464 — Tue, 03 Feb 2009 09:48:15 GMT

hi ,

you can show some lines in the editable mode and some of the lines in non-editable mode by changing the screen properties of table control.

you can write that code in the pbo of the the screen in loop at i_table.

refer the demo program demo_dynpro_tabcont_loop_at.

regards,

Veeresh

Re: Module pool Program table control

Former Member — Tue, 03 Feb 2009 09:58:00 GMT

Try this:

CONTROLS controlname TYPE TABLEVIEW USING SCREEN screenname.

DATA: cols LIKE LINE OF controlname-cols.

LOOP AT controlname-cols INTO cols.

  cols-screen-input = '0'. "input not possible

  cols-screen-input = '1'. "input possible

  MODIFY controlname-cols FROM cols INDEX sy-tabix.

ENDLOOP.

Re: Module pool Program table control

Former Member — Tue, 03 Feb 2009 10:05:09 GMT

Hi Soumya,

Based on some condition we can do, and this condition is 'based on the value in the table control'.

loop at screen.
if screen-group1 = 'GRP1'.
if itab-field eq 'FieldValue'.   -----> condition 
screen-input eq 0 or 1.
modify screen.  
endif.
endif.
endloop.

Check this Link..

[]

Re: Module pool Program table control

I355602 — Tue, 03 Feb 2009 10:36:36 GMT

Hi,

Take the group1 for the textbox field as 'ABC', which needs to be in display mode.

Use this code, its working:-

In PBO:-


MODULE passdata OUTPUT.
  READ TABLE itab INDEX tab_clc-current_line.
  IF sy-subrc = 0.
    if <condition>. "condition on which textbox needs to be in display mode
      LOOP AT SCREEN.
       IF screen-group1 = 'ABC'.
          screen-input = 0. "disable for input
          screen-active = 0.
          MODIFY SCREEN.
        ENDIF.
      ENDLOOP.
    ENDIF.
ENDMODULE.                 " PASSDATA  OUTPUT

Hope this solves your problem.

Thanks & Regards,

Tarun Gambhir

Re: Module pool Program table control

Former Member — Tue, 03 Feb 2009 10:40:16 GMT

Hi,

In table control field screen input = 0 means desable and 1 means enabled. Refer below code.

LOOP AT flights-cols INTO cols WHERE index GT 2.

cols-screen-input = '0'.

MODIFY flights-cols FROM cols INDEX sy-tabix.

ENDLOOP.

Regards

Md.MahaboobKhan

Re: Module pool Program table control

Former Member — Tue, 03 Feb 2009 11:24:38 GMT

Thanks