topic Selection Screen F4 help in Application Development and Automation Discussions

Selection Screen F4 help

Former Member — Fri, 26 Dec 2008 11:50:00 GMT

I am designiing the Selection Screen.Based on the fst value of the selection screen my secound in put help should be seen.

I am using the following code

AT SELECTION-SCREEN ON VALUE-REQUEST FOR pa_sno.

SELECT num

sno FROM zsd_tab_cr_panel

INTO TABLE it_panel

WHERE num = pa_num.

IF sy-subrc EQ 0.

DELETE ADJACENT DUPLICATES FROM it_panel .

ENDIF.

CALL FUNCTION 'F4IF_INT_TABLE_VALUE_REQUEST'

EXPORTING

retfield = 'SNO'

dynpprog = sy-repid

dynpnr = '1000'

dynprofield = 'PA_SNO'

window_title = 'TEST'

VALUE_ORG = 'S'

TABLES

value_tab = it_panel

EXCEPTIONS

parameter_error = 1

no_values_found = 2

OTHERS = 3.

IF sy-subrc <> 0.

MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno

WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.

ENDIF.

after entering pa_num value in selection screen when i press f4 for second field is going initial hence my above code is not owrking.

please suggest me wat to do

Re: Selection Screen F4 help

Former Member — Fri, 26 Dec 2008 11:56:26 GMT

In VALUE-REQUEST event we can't get the screen values, to get the screen values first we have to use

DATA: zdynpread LIKE  dynpread OCCURS 0 WITH HEADER LINE.
  MOVE 'PA_NUM' TO zdynpread-fieldname.
  APPEND zdynpread.

  CALL FUNCTION 'DYNP_VALUES_READ'
       EXPORTING
            dyname     = dyname
            dynumb     = '1000'
       TABLES
            dynpfields = zdynpread.


READ TABLE zdynpread WITH KEY fieldname = 'PA_NUM'

then pass this value to further process

Regards

Sasi

Re: Selection Screen F4 help

Former Member — Fri, 26 Dec 2008 11:59:36 GMT

Hai..

I tried the same thing with FM 'F4IF_INT_TABLE_VALUE_REQUEST'.

It is working well. Iam pating working code here. Hope It may to solve Ur problem.


*&-------To Provyde F4 Help

 DATA : BEGIN OF IT_HELP OCCURS 1,
             VBELN TYPE VBRK-VBELN,
             KUNAG TYPE VBRK-KUNAG,
            END OF IT_HELP.

DATA : IT_DYNP TYPE STANDARD TABLE OF DYNPREAD WITH HEADER LINE.
DATA : V_CUST TYPE KNA1-KUNNR.

SELECTION-SCREEN : BEGIN OF BLOCK B1.
 PARAMETERS : P_CUST LIKE VBRK-KUNAG,
              P_SORD LIKE VBRK-VBELN.
SELECTION-SCREEN : END OF BLOCK B1.

*&------- AT SELECTION SCREEN
*&---------------------------------------------------------------------*
*& parameter P_CUST Value is not assigning directly in this case,
*  so we need to read that value using FM 'DYNP_VALUES_READ'
*&---------------------------------------------------------------------*

AT SELECTION-SCREEN ON VALUE-REQUEST FOR P_SORD.

  IT_DYNP-FIELDNAME = 'P_CUST'.
  APPEND IT_DYNP.

CALL FUNCTION 'DYNP_VALUES_READ'
    EXPORTING
      DYNAME                               = SY-CPROG
      DYNUMB                               = SY-DYNNR
    TABLES
      DYNPFIELDS                           = IT_DYNP.

 IF SY-SUBRC = 0.
   READ TABLE IT_DYNP WITH KEY FIELDNAME = 'P_CUST'.
    IF SY-SUBRC = 0.
     V_CUST = IT_DYNP-FIELDVALUE.
    ENDIF.
 ENDIF.

*&------- To display Salesorders based on Customer

*-------
  CALL FUNCTION 'CONVERSION_EXIT_ALPHA_INPUT'
    EXPORTING
      INPUT         = V_CUST
    IMPORTING
      OUTPUT        = V_CUST.
*-------

SELECT VBELN
       KUNAG FROM VBRK INTO TABLE IT_HELP
                       WHERE KUNAG = V_CUST.

*&---------------------------------------------------------------------*
*& 'F4IF_INT_TABLE_VALUE_REQUEST' This FM is to display requested values
*   as a table on selection screen for selection
*&---------------------------------------------------------------------*

  CALL FUNCTION 'F4IF_INT_TABLE_VALUE_REQUEST'
    EXPORTING
      RETFIELD               = 'VBELN'
      DYNPPROG               = SY-CPROG
      DYNPNR                 = SY-DYNNR
      DYNPROFIELD            = 'P_SORD'
      VALUE_ORG              = 'S'
    TABLES
      VALUE_TAB              = IT_HELP.

Code Formatted by: Alvaro Tejada Galindo on Dec 26, 2008 10:21 AM

Re: Selection Screen F4 help

Former Member — Sun, 28 Dec 2008 17:22:31 GMT

modified ur code ..

 
DATA : it_return LIKE ddshretval OCCURS 0 WITH HEADER LINE. "declare this
AT SELECTION-SCREEN ON VALUE-REQUEST FOR pa_sno.
IF NOT PA_NUM IS INITIAL." drop this and prevalidate this parameter
SELECT num
sno FROM zsd_tab_cr_panel
INTO TABLE it_panel
WHERE num = pa_num.
IF sy-subrc EQ 0.
DELETE ADJACENT DUPLICATES FROM it_panel .
ENDIF.
CALL FUNCTION 'F4IF_INT_TABLE_VALUE_REQUEST'
EXPORTING
retfield = 'SNO'
dynpprog = sy-repid
dynpnr = '1000'
dynprofield = 'PA_SNO'
window_title = 'TEST'
VALUE_ORG = 'S'

TABLES
value_tab = it_panel
return_tab = it_return  "new 
EXCEPTIONS
parameter_error = 1
no_values_found = 2
OTHERS = 3.
IF sy-subrc 0.
MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
pa_sno = it_return-fieldval. "screen field returned 

endif.

i hope u r getting the f4 values as desired when posting this thread ..

then this should return the val when u have selected the field ..just check and confirm