topic Re: Spau _ applying the SNOTE in Application Development and Automation Discussions

Spau _ applying the SNOTE

Former Member — Tue, 04 Nov 2008 15:29:47 GMT

Hi All,

I am working on an issue, I have posted my problem earlier too but didn't resolve it yet. Actually we have applied a SP to or system and after that I am having a trouble with one of the SAP std. program, we have applied a SNOTE before the SP and we looked into it after the SP the changes those were supposed to be in there were not in the program, we downloaded the Note using SNOTE, though it downloaded but didn't make any changes. Then I contacted SAP and they said apply the note manually, so when I tried applying it manually and entered the object key to make the changes in the std. program, it gives me this message "Carry out modification comparison for REPS RFEKA700 first. No changes possible" and when I double clicked on the message it shows me this"

Carry out modification comparison for REPS RFEKA700 first. No changes possible

Message no. EU526

Diagnosis

You are trying to edit an SAP object that has already been changed or enhanced in the current system. This could be

A change (without Modification Assistant)

A modification (with Modification Assistant)

Through an upgrade or the import of a Support Package, an object version that was changed by SAP has been imported. The new SAP version, however, has not yet been compared with the changed version.

System Response

The system will deny access in change mode or enhancement mode until the objects have been compared.

Procedure

Run the modification comparison (SPAU) for the object.

If the object is supported by the Modification Assistant, you can compare/adjust it by clicking the stoplight.

If the object was not changed using the Modification Assistant, but by inclusion of notes using the Note Assistant, the respective notes must be compared/adjusted. If it is not absolutely clear which note caused the object to be changed, you can use the Modification Browser SE95 to perform a search: Expand the subtree "Note Corrections" and then use the search function to search for the object name.

......

Then I tried running SPAU and as soon as I got the results of SPAU I saw the green question mark infront of the object name (which is under the using modification Assistant),and when I clicked on that It showed me few SNOTES, so can you please tell me how should I proceed in this case.

THanks,

Rajeev

Re: Spau _ applying the SNOTE

Former Member — Tue, 04 Nov 2008 15:34:39 GMT

When did you apply the SP? You need to reset the object to original befor eyou apply the SAp Note. Try resetting, but I am not sure how it woudl work for green question mark. if you cant reset to original, ask you basis team to confirm the queue, that should be able to reset the object to original. Then you can apply the note in SNOTe or manually.

Re: Spau _ applying the SNOTE

Former Member — Tue, 04 Nov 2008 15:45:16 GMT

Thanks for the reply, earlier also the SDN users they suggested me to reset the object to the original, but I couldn't see anything or any tab which says reset to original. DO you have any idea of that???

Thanks,

Rajeev

Re: Spau _ applying the SNOTE

GauthamV — Tue, 04 Nov 2008 15:51:13 GMT

hi,

check pavan post in this thread.

[https://forums.sdn.sap.com/click.jspa?searchID=18261924&messageID=3786683]

Re: Spau _ applying the SNOTE

Former Member — Tue, 05 Jul 2011 14:12:23 GMT

Did you got any answer on the same? Please help i am in the same situation as you was in.

Mani

Re: Spau _ applying the SNOTE

Former Member — Thu, 21 Jul 2011 20:17:18 GMT

Below are the steps that I followed to resolve a similar issue:

1) Utilities >> Versions >> Version Management: Note down the transport numbers.

2) Find the SAP Notes corresponding to the transports (SE01) by displaying the transport numbers from step 1.

3) SE95 (Modification Browser): look for the SAP notes from step 2 and Reset the objects in the SAP notes to Original.

Re: Spau _ applying the SNOTE

Former Member — Tue, 27 Nov 2012 17:55:14 GMT

We got the same issue for one of the object and it's fixed by doing the following..

1. Go to SMODILOG table and provide the object name in the OBJ_NAME field and display the entries.

2. then check if any of the records are having the the filed UPGRADE as 'X'.

3. If so, make that field as space(initial).

Thanks,

Hari