topic radio button in Application Development and Automation Discussions

radio button

madan_ullasa — Wed, 25 Jan 2006 10:14:32 GMT

frnds,

i want a solution. i have 3 radiobuttons of same group. and under the 1st rad. button i have some more input fields. Now my requirement is , when i select 2nd or 3rd rad.button i want the all the input fields under rad.button 1 to be disabled. i have done this by 'Loop at scree'.. but i want it to happen immediately when i select any of the other 2 Rad.butonsand not after pressing enter.

regrds,

Madan..

Re: radio button

Former Member — Wed, 25 Jan 2006 10:21:09 GMT

Hi Madan,

Please fidn the below sample code to do that.


PARAMETERS: p_radio1 RADIOBUTTON GROUP g1 USER-COMMAND comm,
p_date1 TYPE sy-datum,
p_radio2 RADIOBUTTON GROUP g1 DEFAULT 'X',
p_date2 TYPE sy-datum.



AT SELECTION-SCREEN OUTPUT.
  IF p_radio1 = 'X'.
    LOOP AT SCREEN.
      CASE screen-name.
        WHEN 'P_DATE1'.
          screen-input = '1'.
        WHEN 'P_DATE2'.
          screen-input = '0'.
      ENDCASE.
      MODIFY SCREEN.
    ENDLOOP.
  ELSEIF p_radio2 = 'X'.
    LOOP AT SCREEN.
      CASE screen-name.
        WHEN 'P_DATE1'.
          screen-input = '0'.
        WHEN 'P_DATE2'.
          screen-input = '1'.
      ENDCASE.
      MODIFY SCREEN.
    ENDLOOP.
  ENDIF.

Hope this will help you.

Thanks&Regards,

Siri.

Re: radio button

hymavathi_oruganti — Wed, 25 Jan 2006 10:21:15 GMT

in loop at screen only u can do it

u assgn to three modif ids

loop at screen.

IF RAD1 = 'X'.

if screen-group = 'r1'.

screen -active = 1

else.

screen-invisible = 1.

...........

.......

modify screen.

endloop.

Re: radio button

Former Member — Wed, 25 Jan 2006 10:22:20 GMT

Use the addition MODIF ID <modid>.

Re: radio button

Former Member — Wed, 25 Jan 2006 11:01:44 GMT

THIS WILL WORK

SELECTION-SCREEN BEGIN OF BLOCK b1 WITH FRAME.

PARAMETERS: R1 RADIOBUTTON GROUP G1 USER-COMMAND flag,

p1(10) TYPE c MODIF ID BL2,

p2(10) TYPE c MODIF ID BL2,

p3(10) TYPE c MODIF ID BL2,

R2 RADIOBUTTON GROUP G1 ,

R3 RADIOBUTTON GROUP G1 .

SELECTION-SCREEN END OF BLOCK b1.

AT SELECTION-SCREEN OUTPUT.

LOOP AT SCREEN.

IF ( R2 = 'X' OR R3 = 'X' ) AND

screen-group1 = 'BL2'.

screen-active = '0'.

ENDIF.

MODIFY SCREEN.

ENDLOOP.

REWARD IF HELPFUL

Re: radio button

Former Member — Wed, 25 Jan 2006 11:30:02 GMT

Hi,

Proceed like this,

1. Define all the parameters to be enabled/disabled when you select a radio button like this,

PARAMETERS p_start LIKE sy-datum MODIF ID XX.

2.Then,in the event "AT SELECTION-SCREEN OUTPUT" check which radio button is selected and activate/ deactivate/ visible/ invisible like,

IF r_write EQ gc_mark.

gv_block = 'XX'. ( Where XX is the MODI name as above)

PERFORM form1_deactivate / form2_activate

ENDIF.

3.In the perform,

LOOP AT SCREEN.

screen-active = '1'.

IF screen-group1 = gv_block(gv_block is set in above

event AT SELECTION-SCREEN OUTPUT).

screen-active = '0'.

ENDIF.

MODIFY SCREEN.

ENDLOOP.

I hope this info is suffice.

Regs,

Venkat Ramanan

Re: radio button

Former Member — Wed, 25 Jan 2006 12:39:44 GMT

parameters : rad1 radiobutton group g1 user-command u1,

name type char20 modif id ra,

rad2 radiobutton group g1,

rad3 radiobutton group g1.

at selection-screen output.

loop at screen.

if rad1 <> 'X' and screen-group1 = 'RA'.

screen-active = 0.

endif.

modify screen.

endloop.