topic Re: ALE for material in Application Development and Automation Discussions

ALE for material

Former Member — Wed, 01 Feb 2006 06:46:51 GMT

I am doing ALE to transfer Material from one server to another using BD10. But I am facing some problem in that.

I am describing the process that I follow for ALE.

I have done following things.

1.Define Logical systems SYS1 & SYS2

2.Assign client to logical system

There I have create 1 client 210 Which will be receiving client. Here I mention Logical system name as SYS2. Client Role as Test.

One client 505 was existing I just change Logical System name to SYS1. Client Role as Test.

Save & back

3.Define Target Systems for RFC Calls

Here in R/3 connections create SYS1 & SYS2 connections.

Details About SYS1 :-

Under Technical settings

RFC Destination SYS1

connection type 3

Description Sending Client

IP address of the sender client 128.6.6.206

System No 00

Under Login Security

Client details of the receiver client.

Details About SYS2 :-

Under Technical settings

RFC Destination SYS2

connection type 3

Description Rceiving Client

IP address of the sender client 128.6.6.111

System No 00

Under Login Security

Client details of the Sending client.

Then SAVE & check remote login. It is successful for both clients.

After that BD64

Create a model view MV01

Then Add message type.

Here mention Sender as SYS1, Receiver SYS2 & message type as MATMAS.

Then select Environment menu & select GENERATE ARTNER PROFILE. Modelview name was already there & as PARTNER SYSTEM mention SYS2.

After saying execute

System SYS1 as a partner type already exists

System SYS2 as a partner type already exists

Port A000000017 with RFC destination SYS2 already exists

Outbound parameters for message type MATMAS MATMAS05 already exist

Outbound parameters for message type SYNCH SYNCHRON already exist

But when I do this for first time I got success message.

Today I tried with new model view

SAVEd IT.

same message when generate artner profile selected. After I select DISTRIBUTE from EDIT menu, system display select receiver of model view there Selct SYS2

Getting following message in RED color.

Outbound parameters for message type MATMAS MATMAS05 already exist

Outbound parameters for message type SYNCH SYNCHRON already exist

Kindly suggest where I am going wrong.

Message was edited by: Diliip Gupchup

Re: ALE for material

Former Member — Wed, 01 Feb 2006 07:22:10 GMT

Hi,

SYS1 and SYS2 already there, so you need to create new logical systems and proceed.

better proceed from scratch.

regards

vijay

Re: ALE for material

Former Member — Wed, 01 Feb 2006 07:23:27 GMT

Hi,

Outbound parameters are set once for any message type.

The settings looks correct. After BD10, what is the status of IDOC?

Thanks

Kamal

Re: ALE for material

Former Member — Wed, 01 Feb 2006 07:44:31 GMT

Hello Kamal,

I am gettting following messages in POPUP type I

1)1 master IDocs set up for message type MATMAS

2)1 communication IDoc(s) generated for message typeMATMAS

Is step ro distribute moelview is necessary?

There I am getting error message in RED COLOR

Model view ZMV01 has not been updated

Rreason: Distribution model is currently being processed

Kindly suggest what should be my next step in receiving client because I am able to see the inbound idocs in sending client not in receiving client (TCODE WE02).

****

When I check the IDOC status it is with status 03.

Regards,

Dilip

Message was edited by: Diliip Gupchup

Re: ALE for material

Lakshmant1 — Wed, 01 Feb 2006 09:24:07 GMT

Hi Dilip,

Have a look at url

http://www.sappoint.com/abap/ale.pdf

This document contains the steps which you are looking for.

Thanks

Re: ALE for material

Former Member — Wed, 01 Feb 2006 09:57:18 GMT

HI Dilip,

There might some problem in BD64 only.

If possible remove the old MVIEW and use the new one.

thanks

eswar